s Oversized Maple Leaf Silhouette From Reclaimed Wood - The Kim Six Fix

Oversized Maple Leaf Silhouette From Reclaimed Wood

Oversized wooden leaf cuttoutReclaimed Lumber Leaf Silhouette SignI’m back with another fall sign project made of “reclaimed” lumber.  I will admit I’m using the term ‘reclaimed’ loosely, because this project could be made from old barn wood, or pallet wood or any old lumber, but mine is actually made from some fence boards I got in the cull lumber section of the hardware store.
Oversized wooden leaf cuttoutI love using this type of wood since they are cheap, and I don’t have to spend hours taking apart pallets, pus they give the look of old wood.
Partridge fall mantel with wooden leaf
For fall I decided I wanted a giant leaf on my mantel, but I didn’t want to do the traditional stenciling method I’ve shared with you a bunch of times.   I was thinking something more along the lines of my chevron Easter Egg project, and so the giant leaf silhouette idea was born.Oversized wooden leaf mantel thanksgiving
This project is pretty easy to make, since the only tool you need is a jig saw.  (You could do this on the scroll saw too, but you don’t really need that much precision)
Fall mantel with leaf pumpkins and rooster

SUPPLY LIST:

Reclaimed boards (I used these fence boards that are less than $2 each.  Mine were actually slighted warped so they were 75% off in the cull lumber section. I needed 3)
Plywood or other backer board
Jig saw (You can see a review of my saw in this post)
Wood Stain (Optional)
Pencil
Nail gun or Wood Glue
Paper Leaf Silhouette at actual size (I used the image below, blown up to 35 inches tall which fit my mantel well)
Maple leaf

TUTORIAL:

Step 1: Print Out Traceable Silhouette

This is always a sticking point for people since unless you go pay to have it printed on large scale paper, it is difficult to get a printout that is big enough.  But I discovered the trick.

-Get your image correctly sized in your photo software.
-Set your PRINT AREA so that the entire image fits (I use a ‘custom’ paper size of the final size of the image)
-Save that large single sheet of paper as a PDF
-Open in Adobe Acrobat (or whatever PDF reader you have) and print from there.  The adobe print window gives you the “Page Scaling” option where you can have it Tile Large Pages” and it will take that large image and split it up for you.  

How to print large image on multiple sheetsYou will have to put those pieces back together like a puzzle and tape them together, but it is still a much easier method than making a run the office supply store for an expensive print.
Oversized leaf silhouette on multiple sheets

Step 2: Transfer Image onto Boards

I lay out my boards on top of my image at first to make sure they are all long enough.
Layout of boards for large silhouette cut out
Next I use a pen to score the line though the paper onto the boards, and then go back and trace over that scored line with a pencil.  REMEMBER YOUR BOARDS ARE LOOSE SO MAKE SURE NOTHING SHIFTS WHILE YOU ARE TRACING!
Tracing silhouette onto reclaimed lumber

Step 3:  Cut along lines with a Jig Saw

Because the boards are separate this is actually pretty easy to do.
Cutting board with jig sawSome of the turns are really sharp, but because you are close to the edge of the board, it is easy to come in from multiple angles. Cutting reclaimed lumber with jig saw
Many boards will end up having multiple pieces cut out from them.. So I used the original silhouette to keep track of where everything went.
Laying out wooden leaf silhouette

Step 4:  Stain Pieces and Backer Board (Optional) 

With my boards, the cut edges were a different color than the front, so I went over all the pieces with some wood stain (I used Red Mahogany by Minwax) sot the cut edges wouldn’t be as obvious, but this is all personal preference. If using truly old lumber, the cut edges may be pretty left as-is.

Step 5: Attach Silhouette to Backer Board

I went back and forth deciding if I wanted to leave small gaps between the boards so it was obvious they were their own board, or if I should squeeze them together as a single silhouette. I decided on keeping the gap, especially after staining them, since i wanted it to look like a leaf from boards, not from a solid piece of wood.   I used a nail gun to attach them, but you could just glue them to the backer board as well.  They are only decorative, so they don’t have to be on there super tight.
Nailing wooden silhouette to board
I am pleasantly surprised how great this project turned out.  It only took me a few hours one afternoon and I have quite the statement piece. Reclaimed wood leaf silhouette It has my creative juices flowing for all the other silhouettes I could create!
Large leaf silhouette wooden mantel fall

If you like large oversized signs from reclaimed wood, here are a few others I have shared previously:






Share this:


I recently removed Disqus comments and converted to the Facebook commenting system.
Thank you for your understanding.







 
Copyright © 2017 The Kim Six Fix. Proudly Blogging on Blogger